AMIKON LIMITED
We'll get back to you as soon as possible.
Place of Origin:
USA
Brand Name:
Bently Nevada
A casing acceleration transducer designed for critical machinery vibration monitoring, including applications that require measurement of gear-mesh vibration.
The 330425 belongs to Bently Nevada's accelerometer product family for critical machinery applications. It is intended for installations where acceleration measurements at the bearing housing or machine casing are required. Sensor mounting, cable selection and measurement-channel requirements should be reviewed as part of the replacement process.
Used for casing acceleration measurements on critical rotating machinery, including gear-mesh vibration monitoring.
Maintenance teams may search for this sensor when an installed accelerometer is damaged, a measurement channel is unavailable, or vibration readings require investigation.
An unavailable or unreliable casing-vibration measurement can limit condition-monitoring coverage and delay the identification of abnormal machine behavior.
Core measurement and electrical specifications are shown below. Additional mechanical, environmental and hazardous-area information is available in the expandable sections.
| Measurement Parameter | Specification | Electrical Parameter | Specification |
|---|---|---|---|
| Sensitivity | 25 mV/g ±5% | Input Voltage | −24 ±0.5 Vdc |
| Acceleration Range | 75 g peak | Bias Current | 2 mA nominal |
| Frequency Response | 10 Hz–15 kHz | Output Bias Voltage | −8.5 ±0.5 Vdc |
| Amplitude Linearity | ±1% to 75 g peak | Grounding | Case isolated |
| Broadband Noise Floor | 0.01 g rms, 10 Hz–15 kHz | Maximum Cable Length | 305 m (1000 ft) |
| Parameter | Specification | Parameter | Specification |
|---|---|---|---|
| Frequency Response | 10 Hz–15 kHz: ±3 dB | Frequency Response | 30 Hz–10 kHz: ±10% |
| Temperature Sensitivity | −11% to +3% typical | Transverse Sensitivity | Less than 5% of axial |
| Mounted Resonant Frequency | Greater than 30 kHz | Resonant Peak | 20 dB maximum |
| Parameter | Specification | Parameter | Specification |
|---|---|---|---|
| Case Material | 316L stainless steel | Weight | 99 g (3.5 oz), typical, without cable |
| Diameter | 23 mm (0.93 in) | Height | 59 mm (2.3 in), including mounting stud |
| Connector | 3-pin MIL-C-5015 receptacle, 316L stainless steel | Mounting Surface Finish | 32 µin rms |
| Mounting Torque | 4.1 N·m (3.0 ft·lb) | Mounting Orientation | Any orientation |
| Operating & Storage Temperature | −55°C to +121°C | Shock Survivability | 5000 g peak, maximum |
| Relative Humidity | 100% condensing, non-submerged | Case Sealing | Hermetically sealed |
| Magnetic Field Susceptibility | 225 mg/gauss, at 50 gauss and 50–60 Hz | IP Rating | Equivalent to IP68 for sensor only |
| Maximum Use Altitude | 2000 m above sea level | Cable IP Rating | Sensor IP rating does not apply to cable |
| Parameter | Published Information | Parameter | Published Information |
|---|---|---|---|
| Approval Option | CSA, ATEX and IECEx multiple approvals | Entity Voltage Ui | 28 V |
| Entity Current Ii | 150 mA | Entity Power Pi | 0.84 W |
| Entity Capacitance Ci | 10.8 nF | Entity Inductance Li | 0 µH |
| Hazardous-Area Connection | Use with associated equipment meeting the applicable intrinsic-safety requirements and entity parameters. | ||
| Zone 2 Connector Protection | Mating connector must provide IP54 ingress protection or better as specified by the datasheet. | ||
| Code / Part Number | Description |
|---|---|
| -01 | ¼-28 UNF integral mounting stud |
| -05 | Multiple approvals: CSA, ATEX and IECEx |
| 127088 | 330400 and 330425 Accelerometer User Guide |
| 00531080 | Mating connector for 330400 and 330425 accelerometers |
| 130539 | 3-conductor shielded 18 AWG cable with 3-socket plug and fluorosilicone elastomer boot at one end, terminal lugs at the other end |
| 16925 | 3-conductor shielded 22 AWG cable with 3-socket plug at one end and terminal lugs at the other end |
| 16710 | 3-conductor shielded 22 AWG armored cable with 3-socket plug at one end and terminal lugs at the other end |
The manufacturer specifies installation on the bearing housing or machine casing. Improper mounting can affect amplitude and frequency response or produce signals that do not represent actual machine vibration.
AMIKON Industrial Supply supports industrial automation spare-part sourcing and order coordination.
RFQ Details: Part Number · Quantity · Destination · Required Date · Machine/System Model
Industrial sourcing, kept practical. AMIKON supports maintenance teams, system integrators and industrial buyers with automation spare-part enquiries, order coordination and international supply support. Our focus is clear part identification, responsive communication and practical procurement assistance.
Send your inquiry directly to us